Blog

Water and honey flow differently – that’s viscosity.

September 20, 2021

Water and Honey Viscosity examples

Water and honey flow differently – that’s viscosity.

Source: AMSOIL Magazine, Preferred Customer Edition. Fall 2021, pg. 10-11

The physical properties of lubricants include important characteristics like viscosity, shear stability, high- and low temperature performance, water resistance and volatility. Lubrication science seeks to optimize a lubricant’s performance by managing these properties through use of different base oils and additives. Of the fundamental physical properties, viscosity – the measure of the internal friction of a liquid, or its resistance to flow – is one of the most critical.

To help visualize the differences in viscosity properties, think about how honey and water flow when poured. Water runs fast and easy while honey flows thick and slow. The contrast is due to their different viscosities. What causes that difference? When external forces such as gravity act on a fluid, the molecules within the fluid begin to move against each other, resulting in molecular-level friction that resists flow. The greater the internal friction, the higher the viscosity of the fluid. How the viscosity of a fluid reacts to changes in temperature, pressure or speed determines how well a fluid can perform the basic functions of a lubricant.

Viscosity, it’s characteristic

Viscosity is an important characteristic to consider when determining which fluid is most suitable for an application. If viscosity is too low, friction between mating components generates heat and excessive wear. A viscosity that’s too high can cause heat, increased energy consumption and a lack of lubrication as the fluid may not be able to pass through small passages as readily.

A lubricant’s viscosity range is often reported by using a grading system such as those established by the Society of Automotive Engineers (SAE) or the International Organization for Standardization (ISO). Requirements for gasoline and diesel motor oils have been set forth in the SAE J-300 Engine Oils Viscosity Classification and the American Petroleum Institute (API) Service Classification. 

Knowing that a fluid’s viscosity is directly related to its ability to carry a load, one would think that the more viscous a fluid, the better it is. However, use of a fluid with a higher-than recommended viscosity can be just as detrimental as using an oil whose viscosity is too low.

Using lubricants with inadequate viscosity for the application may lead to the following issues: 

  • metal-to-metal contact 
  • friction and wear 
  • oil consumption 
  • leaking seals 

Using lubricants with too high a viscosity for the application may lead to the following issues: 

  • increased fluid friction
  • higher operating temperatures 
  • poor cold-temperature fluidity 
  • reduced energy efficiency

The key is to select a fluid with a viscosity that is not too low or too high. The viscosity of an effective lubricant must be adequate to keep moving parts separated under normal operating temperatures, pressure and speed.

Temperature

Lubricant base oils thicken as they cool. As their temperature continues to drop, they eventually solidify. This thickening increases the lubricant’s load-carrying capabilities, but its ability to circulate becomes significantly impaired. On the other hand, fluids thin when heated, decreasing their ability to carry a load and prevent metal-to-metal contact.

Pressure

Proper viscosity for the intended application is critical to ensure that forces applied to the oil do not result in increased component wear. Applying extreme pressure to oil can lead to mechanical shear, which lowers the film strength and leads to metal-to-metal contact and wear. However, viscosity that is too high can cause oil starvation by not flowing through small oil passages. Optimizing viscosity ensures oil can circulate properly and provide adequate film strength on components.

Speed

Whether the application is a grease-filled bearing or oil-filled gearbox, one must consider the lubricant’s optimal viscosity based on the application’s running speeds. As speed increases, components may require a lower-viscosity oil to operate efficiently. 

Furthermore, high viscosity or speed may also increase the lubricant’s film thickness, which increases fluid friction. If the viscosity is too high, fluid friction generates excessive heat that shortens the lubricant’s life.

Viscosity Control

AMSOIL synthetic lubricants are designed to deliver the optimum viscosity for their intended applications. Advanced base-oil formulations and additive packages provide robust protection against viscosity breakdown for reliable protection and performance.

 

Signup for AMSOIL Newsletter and Product NEW Announcements*sign up to our newsletter, then manage you subscriptions

Manage Your Subscriptions:

  • Newsletter
  • AMSOIL Updates
  • Product Updates and Recommendations (NEW Products*)
  • Promotions
Synthetic Lubricants © All Rights Reserved 2024